• Please make sure you have the latest version of Remote Buddy installed. If in doubt, download the latest version, quit Remote Buddy, delete it, empty your trash, then copy the downloaded version of Remote Buddy to your harddrive and start it from there.
• Please make sure, that you have installed the latest version of the Remote Buddy drivers. You can install the drivers using the Setup Wizard (=> access it via the Remote Buddy pulldown menu).
• Check your Remote Buddy settings in the Hardware category. Your remote control should be listed there and the lamp next to it should be green. If you don't find your remote control there, either the Remote Buddy drivers were not installed or installed in an outdated version - or - there is a general problem with the device. For USB devices, plugging the device to another port or resetting the PMU and/or SMC-unit of your Mac® (=> find guides on how to do this for your Mac® in the support area of apple.com) may help. If you can't find it under "USB" in the System Profiler (=> /Applications/Utilities) either, a hardware defect is as well possible.
• Check the batteries of your remote control.
• If your remote control has an on/off switch: make sure that your remote control is switched on.
• If your remote control requires additional receiver hardware: make sure that it is correctly attached to your computer and that it turns up in System Profiler.
• If you use an Apple® Remote, you should also check your system settings. Quit Remote Buddy, then open System Preferences.app > Security. Please make sure that the option to disable the infrared receiver is NOT active and click on "Unpair" should you have paired your Apple® Remote with your Mac®. After that, start Remote Buddy. If your Apple® Remote still doesn't work with Remote Buddy, please also check its preferences for the Apple® Remote. They can be found at Preferences > Hardware > Built-in IR receiver. If support for multiple remote controls is enabled there, ensure that your remote control is checked in the right table (=> you can find the correct entry for your remote control by pressing a button on it).
• If you are using a Keyspan™ RF Remote for Front Row, re-pair its remote control and receiver by simultaneously pressing the small knob on the back of the remote control and the knob on the receiver stick (the knob looks like the blinking LED, except it does not blink).

To enable you to use all capabilities of the IR Receiver of your Mac®, Remote Buddy is using its own driver. In contrast, all other applications with integrated Apple® Remote support usually use the OS X Apple® Remote subsystem.

As long as you're running Remote Buddy, Remote Buddy and its driver are responsible for turning the received button presses into actions. As soon as you quit Remote Buddy, this task is again handled by the OS X Apple® Remote subsystem.

If other applications don't use the interface to the OS X Apple® Remote subsystem correctly, this can lead to the effect that nothing happens when you press a button on your Apple® Remote. For as long as you're running Remote Buddy, issues like this are covered by Remote Buddy and it's driver and are therefore not visible to you. However, as soon as you quit Remote Buddy, the OS X Apple® Remote subsystem is back in control and any issues caused in it by other applications become visible.

Therefore Remote Buddy is neither the cause of the issue nor is it responsible for it. Instead, the cause of the issue exists independently of Remote Buddy. It's located elsewhere and can also only be solved there.

Although our products can't cause any such issues, we're regularly contacted about such issues and asked for help. In order to make locating and fixing the cause of such issues as easy and efficient as possible, we've developed a free diagnostics tool: Remote Control Diagnostics. It can locate issues with a single click and will provide you with information about the issue as well as with instructions on how you can fix it.

There's a bug in the Bluetooth®-stack of OS X® 10.8/10.9 in the context of pairing a Sony® PS3 BD Remote. OS X® 10.8/10.9 will ask you to enter a PIN code when you try to connect your remote control. This problem is known by Apple®.

If you pair your Sony® PS3 BD Remote with your Mac® for the first time

1. Use Remote Buddy's Setup Wizard to pair your remote control
2. Restart your Mac® directly after the pairing was successful, while the remote is still connected.
3. The remote should now work without problems.

If you've already paired the Sony® PS3 BD Remote with your Mac®

1. 10.9 only: Try entering 0000 as PIN and reboot. If you're lucky, that was all you needed to do. If this does not solve your issue, please continue with the steps that follow.
2. First, we'll need to remove the Link Key of your Mac® from the memory of your remote control. Since this remote control can only store one Link Key, it's as easy as pairing the remote control with another Mac®. To do so, open System Preferences > Bluetooth on another Mac® and pair your remote with it.
3. All steps that follow should be performed on the Mac® that you want to use your remote control with.
4. Remove - if it exists - the entry of your remote control at Remote Buddy > Preferences > Hardware ® Bluetooth Receiver. The entry usually is titled "BD Remote".
5. If existant, remove the device "BD Remote" from System Preferences > Bluetooth.
6. Delete the Bluetooth preferences files by entering the following in Terminal.app and hitting return (Warning: this deletes all information about all paired Bluetooth® devices):

   sudo rm /Library/Preferences/com.apple.Bluetooth.plist
   sudo rm ~/Library/Preferences/com.apple.Bluetooth.plist
   sudo rm ~/Library/Preferences/ByHost/com.apple.Bluetooth.*.plist
   

   Please enter your admin password when requested. Then restart your Mac®.
7. Use Remote Buddy's Setup Wizard to pair your remote control
8. Restart your Mac® directly after the pairing was successful, while the remote is still connected.
9. The remote should now work without problems.

These settings are recommended:

General

Search for paired remotes on startup: On.
Stop searching for paired remotes after max .. minutes: Off.
Display pairing instructions and status messages: Off. If you experience problems, you should turn this option back on to aid you in debugging the problem.

Energy saving

Automatically disconnect remotes after inactivity of more than .. minute(s): On, value of 1 minute.
Disconnect remotes when computer goes to sleep: On. The potential power saving with this option is huge. But as the warning says, this will not work with all computers: if you can't wake up your computer with your remote after turning this option on, please turn it off again.