To enable you to use all capabilities of the IR Receiver of your Mac®, Remote Buddy is using its own driver. In contrast, all other applications with integrated Apple® Remote support usually use the OS X Apple® Remote subsystem.

As long as you're running Remote Buddy, Remote Buddy and its driver are responsible for turning the received button presses into actions. As soon as you quit Remote Buddy, this task is again handled by the OS X Apple® Remote subsystem.

If other applications don't use the interface to the OS X Apple® Remote subsystem correctly, this can lead to the effect that nothing happens when you press a button on your Apple® Remote. For as long as you're running Remote Buddy, issues like this are covered by Remote Buddy and it's driver and are therefore not visible to you. However, as soon as you quit Remote Buddy, the OS X Apple® Remote subsystem is back in control and any issues caused in it by other applications become visible.

Therefore Remote Buddy is neither the cause of the issue nor is it responsible for it. Instead, the cause of the issue exists independently of Remote Buddy. It's located elsewhere and can also only be solved there.

Although our products can't cause any such issues, we're regularly contacted about such issues and asked for help. In order to make locating and fixing the cause of such issues as easy and efficient as possible, we've developed a free diagnostics tool: Remote Control Diagnostics. It can locate issues with a single click and will provide you with information about the issue as well as with instructions on how you can fix it.

Please go through all of the following points to check your setup for possible errors:

1. Please make sure that your computer is equipped with Bluetooth® and that it is active. You can enable and disable Bluetooth® at any time through System Preferences.
2. If you only switch on Bluetooth® occassionally: the Bluetooth® stack used by Apple® does seem to need up to a minute after it has been activated, before it can establish connections to devices. During this time, Bluetooth® appears to be active to applications, but isn't fully there just yet.
3. Please make sure the Bluetooth® Receiver in Remote Buddy is active (green "light" in front of its entry in the menu).
4. Before you can use a Wii™ Remote with Remote Buddy for the first time, you need to pair it through the "Setup Wizard". For pairing, open the "Setup Wizard" of Remote Buddy (you can access it in the pull down menu to be found in your system's menu bar behind the Remote Buddy icon) and follow its instructions. If the pair option is greyed out, use the Setup Wizard to install the Remote Buddy Kernel Extension, first.
5. If a remote control has been connected through the setup wizard once, an active Bluetooth™ Receiver in Remote Buddy and pressing buttons 1 and 2 at the same time are sufficient to establish a connection.
6. If not all four LEDs are blinking when pressing button 1 and 2 - or if they blink with different brightness - your battery may no longer hold enough power for the operation of the remote control. Fresh batteries then solve the problem.
7. If the combination of buttons 1 and 2 does not lead to a successful pairing, you'll find a small red knob after removing the battery door, which, when pressed, will also trigger the pairing.
8. In rare cases (we currently know of only one), the remote control itself needs to be reset. Therefore, remove the batteries for at least 30 seconds, then insert them again and try anew to establish a connection. You may possibly have to pair the remote anew, first.

In order to automatically activate the Bluetooth® Receiver on startup, enter the settings, choose "Hardware", then click on "Bluetooth® Receiver". Finally activate the checkbox "Search for supported remotes on startup". Remote Buddy will then automatically look for remote control paired through the "Setup Wizard" on next startup.

The AJAX Remote of Remote Buddy, which you can view and use through your the browser on your iPhone™, works over TCP/IP and HTTP. The iPhone™ does only support these standards over WLAN and EDGE at this point, not via Bluetooth®. Please connect your iPhone™ to the same WLAN as your Mac®, then follow these instructions:

http://www.iospirit.com/products/remotebuddy/guides/ajaxremotesetup/

The Setup Wizard has been exclusively designed and developed for Bluetooth® remote controls, not mobile phones.

This is possible, but not officially supported. Thanks for understanding that we can't offer you any support on this topic.

What you'll usually have to do:

1. Make Remote Buddys AJAX Remote reachable from the Internet: set up a so called port forwarding in the router for the port Remote Buddy's server can be reached at (by default, that's port 8888).
2. Make the Mac® locateable in the Internet: Register at for example DynDNS.org and install the corresponding client
3. The new URL, reachable from the Internet could then be http://mymac.dyndns.org:8888/ .

Here's an article (one of many you can find on the Internet) on this topic:

• Mac World: http://www.macworld.com/2006/08/secrets/octmobilemac/index.php

These are the most frequent causes for this kind of problem are:

• The AJAX Remote is not active. Please check in Remote Buddy's preferences, that you have enabled the AJAX Remote and that it shows the status "active".
• The OS X firewall is active and blocking incoming connections. Please read the entry "How can I define a rule to allow access to port 8888 with active Firewall?" for a step-by-step howto for fixing this problem.
• Bonjour® only works LAN-wide. In order to reach your computer by its Bonjour® name, it needs to be located in the same IP subnet - which in this case means that it must be connected to the same WiFi network. If your computer is connected to the same LAN (wired connection) as the WiFi Access Point, but not to the WiFi Access Point itself, your computer and your device are located in different subnets, whereas Bonjour® services usually can't be announced beyond the boundaries of subnets. Furthermore, the iPhone™ does only support Bonjour® addresses starting with firmware version 1.1.1. Older firmware releases can't make any sense of them.
  The solution - in both cases - is to directly enter the IP of your computer on your device. Complete URLs for all network connections/interfaces of your computer can be found directly within Remote Buddy under "Preferences > AJAX Remote".
• A firewall / router does not forward connections. If you are trying to access your computer from the Internet, only a direct connection using the IP of your internet connection is possible.
  • If your computer has a direct connection to the Internet without any intermediate router, Remote Buddy will show the correct IP address of your computer under "Preferences > AJAX Remote".
  • If your computer is connected to the Internet through an intermediate router, only that router knows your current IP on the Internet. Furthermore, you need to make sure, that it forward connections to port 8888 to your computer. Please consult the manual of your computer to learn whether your router supports that function and how you can set it up.
  • Our service for you: you can let our server tell you your current Internet IP at http://www.iospirit.com/myip/.

Currently, these browsers are officially supported by the AJAX Remote:

• Safari® on iPhone™ with OS 3.0 or later
• Safari® on iPod® Touch with OS 3.0 or later
• Safari® 4 or later

The AJAX Remote is using the latest web standards (like CSS3, which is often only supported sufficiently by Safari®) to utilize the available bandwidth and CPU power efficiently.

IMPORTANT: to use the AJAX Remote, your setup needs to meet all of the AJAX Remote requirements!